收藏本站
j)
k)
l)
m)
n)
o)
p)
If the host has not placed the result of its CRC calculation on D[15:00] since first driving D[15:00] during
(9), the host shall place the result of its CRC calculation on D[15:00] (see 6.5.4.5 ).
The host shall negate – DMACK no sooner than t MLI after the device has asserted DSTROBE and negated
DMARQ and the host has asserted STOP and negated – HDMARDY, and no sooner than t DVS after the host
places the result of its CRC calculation on D[15:00].
The device shall latch the host’s CRC data from D[15:00] on the negating edge of – DMACK.
The device shall compare the CRC data received from the host with the results of its own CRC calculation. If
a miscompare error occurs during one or more Ultra DMA burst for any one command, at the end of the
command, the device shall report the first error that occurred (see 6.5.4.5 ).
The device shall release DSTROBE within t IORDYZ after the host negates – DMACK.
The host shall neither negate STOP nor assert – HDMARDY until at least t ACK after the host has negated –
DMACK.
The host shall not assert – IORD, -CS0, -CS1, DA2, DA1, or DA0 until at least t ACK after negating DMACK.
Figure 14: Ultra DMA Data-In Burst Host Termination Timing
Notes: The definitions for the STOP, HDMARDY, and DSTROBE signal lines are no longer in effect after
DMARQ and DMACK are negated.
6.5.4.4.6 Initiating an Ultra DMA Data-Out Burst
An Ultra DMA Data-out burst is initiated by following the steps lettered below. The timing diagram
is shown in Figure 15: Ultra DMA Data-Out Burst Initiation Timing. The timing parameters are
specified in Table 27: Ultra DMA Data Burst Timing Requirements and are described in Table 28: Ultra DMA Data
Burst Timing Descriptions.
The following steps shall occur in the order they are listed unless otherwise specifically allowed:
a) The host shall keep – DMACK in the negated state before an Ultra DMA burst is initiated.
b) The device shall assert DMARQ to initiate an Ultra DMA burst.
c)
Steps I, (d), and (e) may occur in any order or at the same time. The host shall assert STOP.
d) The host shall assert HSTROBE.
Swissbit AG
Industriestrasse 4
Swissbit reserves the right to change products or specifications without notice.
Revision: 1.20
CH-9552 Bronschhofen
Switzerland
www.swissbit.com
industrial@swissbit.com
C-320_data_sheet_CF-HxBO_Rev120.doc
Page 35 of 101
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SFCF4096H4BK2SA-I-QT-553-SMA FLASH SLC UDMA/MDMA/PIO 4G
SFCF64GBH2BU4TO-I-NU-517-STD FLASH SLC UDMA/MDMA/PIO 64GB
SFN08B4702CBQLF7 RES ARRAY 47K OHM 7 RES 8-DFN
SFP1050-12BG FRONT END AC/DC 1050W 12V
SFP450-12BG PWR SUP 450W 12V 36.6A W/STANDBY
SFSD1024N1BN1TO-I-DF-151-STD FLASH MICRO SD CARD IND S-200 1G
SFSD2048L1BN2TO-I-DF-151-STD FLASH SECURE DGTL CARD SD 2G
SFSD4096L1BN2TO-I-Q2-141-STD FLASH SECURE DGTL CARD SDHC 4G
相关代理商/技术参数
SFCF2048H1BO2TO-I-M0-533-ZP1 制造商:SWISSBIT NA INC 功能描述:FLASH
SFCF2048H1BO2TO-I-M0-543-SMA 制造商:SWISSBIT NA INC 功能描述:FLASH
SFCF2048H2BU2TO-C-MS-527-STD 制造商:SWISSBIT NA INC 功能描述:FLASH
SFCF2048H2BU2TO-I-MS-517-STD 功能描述:FLASH SLC UDMA/MDMA/PIO 2GB RoHS:是 类别:存储卡，模块 >> 存储器，PC 卡 系列:C-440 标准包装:30 系列:- 存储容量:8GB 存储器类型:存储卡 - Extreme III SD?
SFCF2048H2BU2TO-I-MS-527-STD 制造商:SWISSBIT NA INC 功能描述:FLASH
SFCF2048H4BK1SA-C-QT-553-SMA 制造商:SWISSBIT NA INC 功能描述:FLASH
SFCF2048H4BK1SA-I-QT-553-SMA 功能描述:FLASH SLC UDMA/MDMA/PIO 2G RoHS:是 类别:存储卡，模块 >> 存储器，PC 卡 系列:C-300 标准包装:30 系列:- 存储容量:8GB 存储器类型:存储卡 - Extreme III SD?
SFCF2048H4BK2SA-C-DS-553-SMA 制造商:SWISSBIT NA INC 功能描述:FLASH SLC UDMA/MDMA/PIO 2G